To convert a basement window to egress, we make the opening bigger, mostly by cutting down, then set a code-size window and a well. We do this for homes across Nassau County, from Long Beach and Hempstead to Glen Cove, and across Suffolk County, from Huntington and Brookhaven to East Hampton. Most take one day.
Why the Window You Have Probably Won’t Pass
Look at where your basement windows sit. On most Long Island houses they’re up near the ceiling, just above the soil line, and they’re wide but short. That’s fine for light and air. It doesn’t work as a way out, so it won’t pass for basement bedroom egress.
The two most common types we replace:
Hopper windows. Hinged at the bottom, they tilt in from the top. The clear opening is a fraction of the frame, and the sill is usually well over 44 inches off the floor.
Glass block. Often put in to stop drafts or break-ins. It doesn’t open at all, so it counts for nothing as egress.
Under the 2025 Residential Code of New York State, section R319 (see NY egress window requirements), an escape opening needs at least 5.7 square feet of net clear opening (5.0 only for a grade-floor opening, where the bottom of the opening is within 44 inches of the ground outside). It also needs at least 24 inches of clear height and 20 inches of clear width, and a sill no more than 44 inches above the floor. Want to know where yours stands? Measure the open window and run it through the egress window checker.

Can I Make a Basement Window Bigger?
Yes, in most houses. Most enlargements go down, not sideways. The top of a basement window usually sits just under the sill plate and joists, so there’s nowhere to go upward. We cut the foundation below the existing opening to lower the sill and gain height, and widen it if the window needs more clear width.

How to Make a Basement Window into an Egress Window
The job then runs like any egress window installation:
- Dig the well pit outside, down past the new sill.
- Remove the old window or glass block.
- Cut the foundation to the new size with a concrete saw.
- Set, level and seal a code-size window. A casement is the usual choice because it opens fully.
- Install the well, haul away the cut concrete and clean up.
Most of these take one day. A block wall or a deep dig can add time, and we’ll give you the schedule with your quote. Ask at the estimate how the basement is protected during the cut, how the well drains, and, on a block wall, how the open cores along the cut are closed.

Does a 36x36 Window Meet Egress?
It comes down to the clear opening with the sash fully open, not the size of the frame. A clear opening of 36 by 36 inches is 9.0 square feet, comfortably over the 5.7 square foot minimum and the 24 inch and 20 inch minimums. A casement with a 36 by 36 inch frame loses a few inches to the frame and usually still passes on size. A slider that size opens less than half its width, under the 20 inch minimum. Whatever the window, the sill still has to be 44 inches or less off the floor.

What It Costs
The work is much the same as a new egress window: digging, the cut, the window, the well. We price it after seeing the window. For comparison, a new egress window starts at $5,900 installed with a masonry well, $6,500 with a Boman Kemp steel well and $8,900 with a Cambridge ArmorTec block well, and deeper wells cost more. Electrical or plumbing on the inside of that wall can change the plan or the price, and we’ll check for it at the estimate. What an egress window costs on Long Island has the detail.

When Enlarging Isn’t the Right Call
Sometimes the old window is in the wrong place. If it sits behind a deck that can’t come up, over a driveway or right at a property line, there may be no room for a 36 inch egress window well in front of it. In that case it’s often simpler to leave the old window alone, or close it up, and cut a new egress opening on a wall with space outside. We’ll show you both options at the estimate.

Before You Start
The enlarged opening is a new egress opening, so it needs a building permit from your town, city or incorporated village and an inspection when it’s done. See egress window permits on Long Island.
Call or text (516) 390-8891 to set up a free onsite estimate, and we’ll tell you whether yours can be enlarged where it is. Other jobs are on our egress window services page.
Can I make a basement window bigger?
Usually, yes. We cut the foundation below the existing window, and wider if it needs more clear width, so the new opening meets section R319 of the 2025 Residential Code of New York State. Then we set a code-size window and install a well outside. The top rarely moves, because the sill plate and floor joists sit right above most basement windows.
Can I just replace my basement window with a bigger egress window in the same opening?
Rarely. Most basement window openings are too short and sit too high on the wall to pass, so a plain basement window replacement in the same hole won't give you egress. The wall has to be cut down to make the opening taller and bring the sill within 44 inches of the floor. Then the window and a well go in.
Is a hopper window an egress window?
Almost never. A hopper tilts in from the top and sits high on the wall, so its clear opening and sill height fall short of the code. A basement escape opening needs at least 5.7 square feet of net clear opening, 24 inches of height, 20 inches of width and a sill no higher than 44 inches. A hopper usually misses on all of them.
Does a 36x36 window meet egress?
It depends on the clear opening, not the frame. A casement with a 36 by 36 inch frame usually passes on size once the frame is subtracted, and the sill still has to be 44 inches or lower. A 36 inch slider opens less than half its width, under the 20 inch minimum, so it fails. Check yours with our egress window calculator.
Can a glass block basement window be converted to egress?
Yes. We remove the glass block, cut the opening larger and lower, then set an egress window and a well. Glass block doesn't open at all, so as it stands it gives no escape opening. Many were put in to stop drafts or break-ins, and a modern casement with a lock does both jobs while still letting someone out.
How much does it cost to enlarge a basement window for egress?
We price it after seeing the window. The work is much the same as a new egress window: digging, the cut, the window and the well. For reference, a new egress window starts at $5,900 installed with a masonry well. Deeper wells, a block wall, or wiring and plumbing on the inside of that wall can raise the price.
- NYS Department of State, notice of adoption of the 2025 Uniform Code
- 2024 IRC section R319.2, ICC Digital Codes
Last reviewed October 21, 2026.





